Agricultural machinery exhibits "World Soil and Tillage Show"

AGCO GmbH – Challenger Pavilon 11 D Main stand: 9 C23

Challenger MT 800 for soil working and seed bed preparation. Ground contact area and ground adjustment are vital in seed bed preparation to avoid soil compactions and thus secure yields sustainably. Transfer of tractive force and area working rates are discussed intensively on business farms and realised by the combination of track technology and large working widths. The right timing and strength are the key to success in our present age!  

Pavilon 11 C Main stand: 9 E05
The 936 Fendt-Vario in operation in the field during the cultivation year. Four special field assignments are shown using miniature models of the tractor and respective trailed implements. The machine combinations show work procedures in which „good agricultural practice“ ensures reduction of soil erosion and soil compaction, as well as conservation of soil fertility.

Amazonen-Werke Pavilon 11 D Main stand: 14 A16

AMAZONE‘s 3C arable farming concept describes procedures and machinery for cultivation. The objective is site-appropriate and cost-optimised tillage and cultivation. The intensity of tillage and drilling operations can be varied. In ploughless cultivation the quantity and distribution of the straw determine the mixing-in intensity. Oxygen and water supply are the crucial criteria for the loosening depth

APV Pavilon 11 C Main stand: 11 E20

Pneumatic seeder PS 250 M2 from APV: The pneumatic seeder PS 250 M2 is suitable for placing all kinds of seed (oilseed rape, clover, grass, lucerne, cereal grains, …). It can be used multifunctionally throughout the year in a single pass together with a tillage implement. The optimal implement for drilling, from 1.5 – 300 kg/ha and working widths of 2 – 7m.

Pavilon 11 D Main stand: 11 E20
Pneumatic seeder PS 600 M1 from APV: The pneumatic seeder PS 600 M1 is suitable for placing all kinds of seed (oilseed rape, clover, grass, lucerne, cereal grains, …). It can be used multifunctionally throughout the year in a single operation together with a tillage implement. The optimal implement for drilling, from 1.5 – 400 kg/ha and working widths of 4 – 12 m.

Auf der Landwehr Pavilon 11 C Main stand: 11 A31

TERRAFLOW – The active roller combines continuous re-consolidation of the soil with safe depth guidance and intensive crumbling to create an erosion-inhibiting soil structure. The active work rings produce the uniform soil structure, clean the roller, and prevent stones from becoming caught.

Bourgault Industries Pavilon 11 B Main stand: 12 B70

Bourgault Industries Ltd. is an agricultural implement manufacturing firm that specializes in seeding systems that enable producers to be effective stewards of the land and manage a profitable business. Each seeding tool marketed by Bourgault will help producers address the particular needs of each region, yet all will offer the same minimal risk of seed damage when equipped for minimal or zero till operation.

CGS-Tyres Pavilon 11 D Main stand: 12 F11

Continental SuperVolumeTyre (SVT) from Mitas a.s.: The new tyre concept has a larger volume than standard tyres. Thanks to the air volume the tyre offers high loadbearing capacity at low pressure and is hence exceptionally gentle to the soil.

Claas Pavilon 11 D Main stand: 4 C22

RUBBER TRACK CHASSIS FOR LEXION 600/580/570/560; TERRA TRAC chassis. This unites the technological advantages of wheeled and tracked vehicles. The axle suspension supplies maximum riding comfort and prevents vibrations, shocks and rocking. Large ground contact area and uniform weight distribution are easy on the soil, coupled with maximum traction.

CTF Europe LTD
Pavilon 11 B Main stand: 11 F53

Soil compaction from field traffic increases production costs, reduces crop returns and damages the environment. Controlled Traffic Farming (CTF) is a discipline that confines all soil compaction to the least possible area of permanent traffic lanes. CTF thus reduces costs and increases crop returns while making farming simpler, less time consuming, and with fewer and less negative environmental impacts.

Danagri Pavilon 11 C Main stand: 11 C12

DTE precision drill. The DTE unit of the pneumatic precision drill „Becker Aeromat“ works with 380 mm cutter discs that are depth-guided on both sides and is suitable for sowing maize, beans, sunflowers etc. under mulch seeding conditions. Preliminary tillage is advisable with a view to creating favourable germination conditions, but not absolutely necessary in light soil conditions.

Grasdorf Wennekamp Pavilon 11 D Main stand: 12 D11

Grasdorf Wennekamp specialises in disc and special wheels. We produce and supply wheels and tyres for your applications. Our proven precision and quality inspire leading agricultural, forestry and construction machinery manufacturers to use the Grasdorf wheel (Grasdorf-Rad®).

Güttler GmbH Pavilon 11 D Main stand: 11 B04

Self-cleaning prismatic rollers from Güttler. The Güttler rollers create an ideal seed bed – firm beneath and loose on top. This conserves valuable soil humidity and prevents water and wind erosion. Also ideal for greenland renewal. Outstanding self-cleaning properties, so ideal in combination with all tillage implements. The rollers quickly pay for themselves by high field emergence rates and fewer seed bed preparation passes.

HEKO Konrad Hendlmeier Pavilon 11 B Main stand: 11 B32

HEKO Turbo-Mix share: Easy-drawing share with mixer panels of various widths, plugged on in front of the share stem. Enhances mixing work up to three times over. The mixing panel is mounted approx. 15 cm behind the share tip at the share neck. The lower edge of the exchangeable mixing panel is countersunk in a recess in the share running crossways to the direction of work. The width of the mixing panel can be up to 50 % of the working width. When the mixer panel is dismounted the implement works like a conventional share.

HE-VA Pavilon 11 D Main stand: 11 F20

HE-VA Till-Seeding: Using a HE-VA Sub-Tiller mounted with HE-VA Multi-Seeder an extremely simple and safe way to establish winter oil rape seed is guaranteed. This system is a super way to seed oil rape because the radicle of the oil rape does not like hard soil. Calculated price: 4 m wide machine and 200 ha/year, 35 EUR/ha

Horsch Maschinen Pavilon 11C Main stand: 11 E21

The economic viability of a farming method is mainly determined by the intensity of tillage (working depth, number of passes). When developing and adapting farming systems, soil and climate are the main factors to consider. With 30 years of experience in conservation tillage, HORSCH offers Know How and technology for all arable farming regions in the world.

IMANTS Pavilon 11 C Main stand: 11 F11

IMANTS rotary spading machine: Spading is proven to be significantly cheaper then ploughing. Primary and secondary tillage in one pass. University of Wageningen: significantly and reliably lower (22%) fuel consumption than ploughing and a reliably higher work rate (56%). Cultivation can be combined with seedbed preparation and seeding in one pass.

John Deere Pavilon 11 B Main stand: 4 A22

Conserva PakTM opener. Hydraulic shanks for precise seed and fertilizer placement will enable minimal tillage disturbance system. Row spacing: 23/30cm. These openers allow seed and fertilizer separation vertically from 5 up to 11,5cm of and provide consistent depth control for good seed placement without seed burn.

Pavilon 11 C Main stand: 4 A22
Seeding coulter Series 90: The single disk coulter guarantees precise seed placement at the set depth even under difficult conditions. Can also be used for direct drilling. Double disk coulter: Double disk coulters cut mulch toppings up to 45% cover with offset disk. Both systems operate with an active coulter pressure system.

Pavilon 11 D Main stand: 4 A22
MaxEmerge Plus. MaxEmerge row-units are an evolution in seeding accuracy, rowunit strength, and adjustability. The ductile iron shank is the foundation of the row unit. The seed metering system is simple and gains a more accurate seed spacing in any crop. Anything from no-till to sticky gumbo and everything in between can be planted with this row unit.

Köckerling Landmaschinenfabrik Pavilon 11 B Main stand: 11 A20

The Köckerling drilling element is a 6cm wide tine that is guided by a support roller. The roller and share are mounted on the frame with plate springs. A hydraulic cylinder supports the element. The cylinder length is altered to adjust the drilling depth, adapt to the soil, and guard against stones. All the cylinders are controlled at the same time. The pre-tensioning of the springs indicates the drilling depth.

Kuhn Pavilon 11 B Main stand: 6 C25

Appropriate tillage and drilling process. Complete programme for a wide variety of methods, taking agronomic, environmentally-relevant and economic parameters into account. Display boards showing various concepts adapted to both West European farming conditions and large-scale farm management.

Kverneland Pavilon 11 C Main stand: 5 C34

Accord Optima HD – High performing mulch drilling with low power requirement. The trailed machine has a high capacity with a 1,200 l fertiliser tank and requires little pulling power, starting at 80 hp (8 rows) for normal and mulch drilling, even under heavy conditions. Exact depth guidance thanks to advance oscillating wheels. Individual weight of the coulter row 130 kg, and 100 kg ballast can be carried. Electrical drive (e-drive) available as an option.

Lemken GmbH Co KG Pavilon 11 C Main stand: 11 A40

Lemken offers appropriate tillage and seeding systems for all soil conditions and locations depending on the crop sequence, intensity and tillage methods. This ensures a maximum of soil stabilisation coupled with a minimum of water loss. Appropriate reconsolidation and precision drilling are explained with assemblies and project studies.

Michelin Reifenwerke Pavilon 11 D Main stand 12 B18

AXIOBIB super-wide tyres for the top performance class from 250 to 500 hp. Thanks to the Ultraflex technology, low pneumatic tyre pressure and high load-bearing capacity guarantee gentler treatment of the soil when working with heavy weights. Outstandingly suitable for cultivation methods requiring high pulling forces without having to dispense with a maximum of soil conservation and diesel efficiency.

Pavilon 11 D Main stand: 12 B18
CARGOXBIB soil-conserving radial ply tyres for trailers and other trailed implements. Distinctly optimised rolling resistance and high load-bearing capacity make it possible to treat the soil gently as well as to work cost-effectively. Thanks to the special carcass structure, ideally suited for air pressure control systems. Precise guidance and large ground contact area round off the product properties.

Molbro Pavilon 11 C Main stand: 11 E09

Molbro tillage implements create optimal growth conditions. Minimal energy outlay for mechanical tillage. Soil erosion is minimised by precision implements. Minimises the rate of plant protection agent and fertiliser application. Higher yield of high-grade foods thanks to Molbro work implements and recommendations.

A. Pöttinger Maschinenfabrik Pavilon 11 B Main stand: 6 C39

Sustainable solutions for successful arable farming. Farmers have to decide on the right technology depending on their soils and crops. Pöttinger offers a variety of methods for practice – conventional ploughing, mulch drilling and mulch direct drilling.

Rabe Agri Pavilon 11 B Main stand: 11 C21

Rabe Parallel drilling system (PSS unit). Soil unevenness is compensated crossways by top-mounted rubber bearings (for one tandem element each) and lengthways by plate springs for each individual drilling unit. Individual stone guards, optimal running smoothness, even at high working speeds. Transverse forces are neutralised by tandem unit. Little wear (no turning point). Self-supported drilling system, precise placement depth thanks to reconsolidating, follow-on depth guide roller.

Reterra Pavilon 11 D Main stand: 14 D22

Compost application in plant production helps in cases of dry stress. Enhanced biological activity of the soil and improved water bonding make a major contribution to a balanced water regime and alleviate or prevent dry stress. This gives farmers a cost-effective alternative for coping better with inclement weather due to climate change in future.

Strom Export  Pavilon 11 C Main stand: 11 E12

Systém Quick-Stop®. Patented system. The rolled plough column made of high-grade spring steel permits micro vibrations to be used for self-cleaning without strippers. Also reduces the size of the cut-off bottom beam. Can be used in very stony conditions. The Quick-Stop® system also includes side guidance of the plough columns to keep a constant distance between discs. Quick-Stop® is used in DISCLAND LC, LN and SWIFTER SD.

VÄDERSTAD Pavilon 11 B Main stand: 11 C31

A model landscape (scale 1:32) shows three plant production methods. Variant 1: light soils with intensive methods: Carrier (short disc harrow) + Cultus (cultivator) + Spirit (drilling machine). Variant 2: heavy soils with close crop sequences: TopDown (one-pass cultivator) + Rapid (drilling machine). Variant 3: border locations (due to water etc.): Seed Hawk (direct drilling method).

Vogel & Noot Landmaschinen Pavilon 11 B Main stand: 11 E31

VN MultiQuick – share changing in seconds. Quick changing systems for cultivator wear parts, for both share tips and winged shares (unique and patented). Allows wear parts to be changed in seconds without any tools and thus leads to uncompromisingly cost-effective tillage with the cultivator.